Sub hook up kit

sub hook up kit

Can I connect two 4-ohm subs together?

Greg, Two DVC 4-ohm subs can only get wired together to form a one-ohm load, a 4-ohm load, or a 16-ohm load. You know you can turn the volume down on a sub, if the amp makes it too loud and out of balance with the rest of the music.

How to wire subwoofers and amplifiers together?

For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size. Now that youve seen how to wire subwoofers and amplifiers together, you can knowledgeably shop Crutchfields extensive selection of subwoofers and amplifiers . We also carry amp wiring kits, speaker wire, RCA cables , capacitors, and much more.

What size wire do I need to wire a subwoofer?

Wire All the wires depicted in the Subwoofer Wiring Diagrams are speaker wires. For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size. [Shop for speaker wire]

Can I run a 4-ohm subwoofer with a 5-channel AMP?

Aizak, For speakers, use the wiring diagrams for SVC 4-ohm subs, as almost all aftermarket speakers are single voice coil 4-ohm devices. Have a Alpine MRX v70 4 channel+mono power. Wanting to just run sub power connection using amp. Possible? Mike, You can use one channel of a 5-channel amp for your bass and leave the other four channels unused.

How do you wire a 4 ohm subwoofer?

They are 4 ohm dual voice coil subs, so wiring each VC in parallel and then each sub in parallel will present a 1 ohm load. wiring each VC in parallel and then each sub in series will be a 4 ohm load.

Is it possible to wire two 4-ohm subs into a 2-ohm load?

Is it possible to wire two 4-ohm DVC subs into a 2 ohm load? Ive heard both yes and no. Wouldnt it work if I just used one voice coil to wire it instead of two? I have a monoblock amp. (Hifonics ZRX1500.1D) no but you can get to 4 ohm.....not great...a little low on power at 4 ohm....or go to 1 ohm, just make sure you have plenty of ventilation.

How many ohms do I need to connect two speakers?

Cut a section of speaker wire for each speaker you want to connect and strip away 1/2 inch of plastic coating from the wire on each end. Add up the total ohms for all speaker pairs, which in this example would be 4+4 (8) and 8+8 (16).

How to wire a 4 ohm to a 16 ohm coil?

wiring each VC in parallel and then each sub in series will be a 4 ohm load. and then series and series again will be 16 ohm. You only need to use one coil on each sub, then run them in parallel and you will have a 2 ohm load.

Wires sized 12- to 16-gauge are recommended for wiring subwoofers. There will be no audible difference between them; the larger cable will simply have less power loss. Is 12 gauge speaker wire good for subwoofers? If your amplifier has a greater power rating, such as 100 watts or 600 watts, you should use 12 gauge cable.

What gauge wire is used for subwoofers?

Can I wire my subwoofers at 4 ohms?

If you decided to wire the subs at 4 ohms, you would have to find an amplifier that puts out 800 watts of power at 4 ohms, which can be very expensive. Let’s keep the same subwoofers but choose a two channel amplifier.

Can I use 2 ohm speakers on a 4 ohm AMP?

When you connect 4 ohms speakers to a 2 ohm amp, you’re connecting two different values of power across a load. So, yes–you can use 2 ohm speakers on a 4 ohm amp! How does impedance change the signal delivered to a speaker? Speakers have impedance as well as resistance.

How many speakers do I need for a 4 channel amp?

System 1: 2 speakers (parallel wiring) to each front channel = 2 Ohms x 2 + 1 subwoofer wired for 4 Ohms on the rear channels bridged for more power. This is the first and best choice for most modern 4 channel amps.

How many ohm resistors do I need for a 4 channel amp?

If you’re wiring 4 speakers and a subwoofer to a 4 channel amp, by adding 60 ohm resistors to the rear speakers you’ll drop the volume by 24dB (decibels). The result will be that the sound is “faded” to the front and the rear speakers won’t be too loud. Following the example I’ve provided here in the diagram above it’s pretty easy.

Related posts: